http_load man page

http_load(1)                                                                                                      http_load(1)

       http_load - multiprocessing http test client

       http_load [-checksum] [-throttle] [-proxy host:port] [-verbose] [-timeout secs] [-sip sip_file] [-cipher str] ( -paral-
       lel N | -rate N [-jitter] ) ( -fetches N | -seconds N ) url_file

       http_load runs multiple http fetches in parallel, to test the throughput of a web server.   However  unlike  most  such
       test clients, it runs in a single process, so it doesn't bog down the client machine.  It can be configured to do https
       fetches as well.

       The -checksum flag tells http_load to do checksums on the files fetched, to make sure they came across ok.  The  check-
       sums  are  computed  the  first  time each URL gets fetched, and then recomputed and compared on each subsequent fetch.
       Without the -checksum flag only the byte count is checked.

       The -throttle flag tells http_load to throttle its consumption of data to 33.6Kbps, to simulate access by modem  users.

       The -proxy flag lets you run http_load through a web proxy.

       The -verbose flag tells http_load to put out progress reports every minute on stderr.

       The -timeout flag specifies how long to wait on idle connections before giving up.  The default is 60 seconds.

       The  -sip  flag  lets you specify a file containing numeric IP addresses (not hostnames), one per line.  These get used
       randomly as the *source* address of connections.  They must be real routable addresses on your  machine,  created  with
       ifconfig, in order for this to work.  The advantage of using this option is you can make one client machine look like a
       whole bank of machines, as far as the server knows.

       The -cipher flag is only available if you have SSL support compiled in.  It specifies a cipher set to use.  By default,
       http_load  will  negotiate  the highest security that the server has available, which is often higher (and slower) than
       typical browsers will negotiate.  An example of a cipher set might be "RC4-MD5" - this  will  run  considerably  faster
       than  the  default.   In addition to specifying a raw cipher string, there are three built-in cipher sets accessible by
         * fastsec - fast security - RC4-MD5
         * highsec - high security - DES-CBC3-SHA
         * paranoid - ultra high security - AES256-SHA
       Of course, not all servers are guaranteed to implement these combinations.

       One start specifier, either -parallel or -rate, is required.  -parallel tells http_load  to  keep  that  many  parallel
       fetches  going  simultaneously.   -rate tells http_load to start that many new connections each second.  If you use the
       -rate start specifier, you can also give the -jitter flag, telling http_load to vary the rate randomly by about 10%.

       One end specifier, either -fetches or -seconds, is required.  -fetches tells http_load to quit when that  many  fetches
       have been completed.  -seconds tells http_load to quit after that many seconds have elapsed.

       The url_file is just a list of URLs, one per line.  The URLs that get fetched are chosen randomly from this file.

       All flags may be abbreviated to a single letter.

       Note  that  while the end specifier is obeyed precisely, the start specifier is only approximate.  If you use the -rate
       flag, http_load will make its best effort to start connections at that rate, but may not succeed.  And if you  use  the
       -parallel flag, http_load will attempt to keep that many simultaneous connections going, but may fail to keep up if the
       server is very fast.

       Sample run:
           % http_load -rate 2 -seconds 300 urls
           591 fetches, 8 max parallel, 5.33606e+06 bytes, in 300 seconds
           9028.87 mean bytes/connection
           1.97 fetches/sec, 17786.9 bytes/sec
           msecs/connect: 28.8932 mean, 44.243 max, 24.488 min
           msecs/first-response: 63.5362 mean, 81.624 max, 57.803 min
           HTTP response codes:
             code 200 -- 591


       Copyright (C) 1998,1999,2001 by Jef Poskanzer .  All rights reserved.

                                                       15 November 2001                                           http_load(1)

How to install NAGIOS NRPE plugin under Debian Linux

NRPE allows you to remotely execute Nagios plugins on other Linux/Unix machines. This allows you to monitor remote machine metrics (disk usage, CPU load, etc.). NRPE can also communicate with some of the Windows agent addons, so you can execute scripts and check metrics on remote Windows machines as well. Citation.

You may follow the steps to install NRPE in any of the following ways:

1) Steps (compiling from sources)

First, you should download the latest NRPE version from HERE.

Then, install some required packages:

apt-get update
apt-get install build-essential libssl-dev

Unpack the NRPE addons, configure and install:

cd /opt
tar xvfz nrpe-2.12.tar.gz
cd nrpe-2.12
./configure --enable-command-args
make all
make install-plugin

2) Steps (using apt binaries)

apt-get update
apt-get install nagios-nrpe-plugin

NRPE can now be invoked using the following:


Another option would be to create a symlink to make the invocation easier:

ln -s /usr/lib/nagios/plugins/check_nrpe /usr/bin/check_nrpe